Hamburg, Germany | Global Service in 52+ Countries
[email protected] | +49 (0) 40 123 456

I Audited 8 Years of Commercial Refrigeration Spending. That '18% Cheaper' Quote Cost Us $11,800.

The Quote That Looked Like a Win

In September 2024, we spec'd out a 3-ton Bohn evaporator and matching air cooled condenser for a new 12×16 walk-in. I sent the spec sheet out to four distributors. The quotes came back with a spread that hurt to look at — the lowest was 18% under the highest.

$27,400 versus $32,600. Same accessory list. Same spec sheet. Same warranty terms on paper.

I went back and forth on it for three days. The higher-priced distributor had a better doc pack and a faster parts desk — I could feel that gap in my gut. But we were behind on the build, and the lower number fit the timeline better. I went with the cheap one. Told my CFO I'd found $5,200 in found money.

She nodded. I then did something I've been telling myself not to do since I took over this budget in 2016 — I compared unit price on a line item that has a service tail longer than the install.

It took about five weeks for the real invoice to come due. Here's what that looked like.

Why 'Cheaper' Refrigeration Quotes Look So Good on Paper

I'm not going to pretend cheap is always wrong. It isn't — we run tight margins on every project, and negotiating a fair unit price is part of my job. Half my week is bid review and vendor follow-up.

But after eight years of tracking invoices, I've learned one pattern: when a Bohn evaporator or air cooled condenser comes in 15–20% under the pack, that gap is being pulled from four or five places that never show up on the front of the quote.

1. Documentation — the part that wasn't quoted

We hit this in week one. The compressor wouldn't fire, and the tech showed up with a model tag, a generic manual, and Google.

Turned out to be a wiring sequence issue. The wiring diagram for that specific Bohn evaporator existed — it just sat in the distributor's folder and never made it with the unit. Three hours to sort out.

Three hours on a small refrigeration shop is not cheap. We run around 15 service calls a month at roughly $85 per hour. That's $255 on an order we'd already paid to have installed.

I've also bought Bohn systems that came with the naming table, wiring diagram, defrost control settings, and selection data all in one packet. Our tech walked in, opened the panel, and knew exactly what he was looking at. That still holds — pull up a Bohn parts order today and the nomenclature tells you what you're getting. You aren't guessing whether a coil or a fan motor will fit.

That's not a soft benefit. That's real money saved on the service ticket side.

2. Part availability and lead time

When the defrost timer on a cheaper evaporator goes bad, the call shifts from 'repair' to 'wait.' If the distributor doesn't stock the platform — and the supplier network behind it is thin — you wait. And if there's product in the box, waiting is expensive.

We got lucky. Nineteen hours for the part to land. No frozen product in the walk-in yet at that point. If there had been, it would've been a different story.

We keep a refrigerated air dryer on our shop compressor and it's been running nearly three years with nothing but filter changes — because it's on the PM schedule and the parts are standard. That's what a good supply chain feels like. The cheap evaporator wasn't giving us that.

3. Energy — the long-tail premium nobody quotes

This is the one that bleeds. A lower-efficiency evaporator — worse frost management, different fan deck, sloppier defrost cycles — shows up on the utility bill year after year.

According to the U.S. Department of Energy (energy.gov), commercial refrigeration accounts for roughly 14% of electricity use in food service buildings. A 5–10% efficiency gap on a small walk-in evaporator can run several hundred dollars a year in a climate like ours. Never on the quote.

I ran the math retroactively: if our cheap unit was running 6% behind on efficiency at our duty cycle, that's about $380 a year in extra power — and nobody on my team would ever catch it line by line.

4. Service response

'Standard warranty' on the quote meant: we'll get to it. Sometimes Friday night, sometimes Monday.

The warranty promise works the same way a snow blower warranty does — it's not what the flyer says, it's whether it starts when the first storm drops. On a $28,000 evaporator holding product at 35°F, the 'first storm' is a Friday evening in a cold snap.

You pay for the hours you sit waiting.

What Those Five Weeks Actually Cost Us

I built the retroactive invoice myself, and I'll be honest — I undercounted the first pass. If I remember correctly, the total landed around $11,800. Maybe closer to $11,900, I'd have to pull the procurement system and check.

  • Tech diagnostics and rework: roughly $2,400. Most of that was the missing documentation — three service dispatches where one would've closed it.
  • Emergency product relocation: about $3,200. Nineteen hours of moving product to our backup freezer plus transport.
  • Extra power: roughly $95 in the first quarter. Annualized, that tracks to the $380–420 range.
  • Refrigerant top-off and two unnecessary evacuations: about $1,100. One fitting failed and vented charge.
  • My time: at least 14 hours in the procurement system hunting parts, chasing the distributor, and doing a post-mortem with our maintenance lead. Call it $870 at our internal $62/hr loaded rate.
  • Redundant labor: I put about $1,800 against two extra call-outs from our maintenance team.

Add it up and it lands somewhere between $9,465 and $11,800, depending on how I value my own time. Call it close to $11,800 by the time I stacked it all in. And honestly? There's still probably $600 of small stuff I didn't track cleanly after the evacuation.

The 'savings' side of the ledger was $5,200.

The hidden cost was more than double the original savings. If those rows had been on the TCO sheet at bid time, the higher-priced unit would have been the easy call.

What grates on me most is that this was avoidable. I already knew about the documentation gap and the parts question before this order went out. But my TCO sheet only had room for quote, freight, and tax. So the costs I couldn't see didn't exist when the decision was made.

What I'd Do Differently — and What I've Since Built In

Part of me wants to pin this on the distributor. The other part knows this one's mine — I had a TCO sheet and I didn't use it.

Here's what I've changed. I put it directly into our procurement process at the end of last year:

1. Require documentation as a line item in the RFQ

I now ask for the nomenclature table, wiring diagram, selection curves, and defrost control documentation at bid time — not after install. If a supplier can't produce standard docs, that's a signal about what you're going to lose later.

2. Put everything on one TCO sheet

We now have five columns: unit price, expected install cost, service response time based on historical data, projected annual energy based on equipment efficiency data, and expected parts cost at failure rate on comparable deployments.

It sounds dramatic to put it next to a bathroom exhaust fan replacement, but I'm evaluating a $180 fan replacement in our office restroom using the same five columns. Cost logic doesn't change with equipment size — only the multipliers do.

3. Bring our maintenance lead into the quote review

This was the easy one. Our maintenance team used to see the equipment after I'd picked it. Now they see the quotes first. They've already flagged one bad condenser pick and a fan deck that didn't match the load profile. That alone paid for the process change.

4. Treat '15–20% cheaper' as a question, not an opportunity

I don't automatically swipe left on a low bid anymore. I ask: what's the cut? If the answer doesn't hold up — documentation, parts, energy, warranty speed — I assume there's a cost somewhere I haven't priced yet.

The Bottom Line

If you're procurement for a refrigeration shop or you're managing the build budget at a cold storage contractor, here's the whole lesson in one line: unit-price comparison is fine. Just add two more columns.

After that $5,200 gap turned into an $11,800 bill, I'm convinced of something I'd have argued against five years ago — the cheapest total cost in a refrigeration bid rarely sits at the top of the quote sheet.

Next time a Bohn evaporator or air cooled condenser bid comes in 18% under the pack, don't celebrate first. Ask the distributor where the hidden cost went. If the answer doesn't hold, look at your TCO sheet before you sign.

Then call the maintenance lead. Before the bid review, not after.

WhatsApp LinkedIn
author-avatar
Elisa Nordberg

Elisa Nordberg writes about air-cooled and water-cooled industrial chillers, modular glycol systems, and screw, scroll, and centrifugal configurations for process and comfort cooling. Her evaluations reference ISO 5149 and AHRI 550/590 practices while comparing cooling capacity, COP, IPLV, compressor lift, fluid flow, and evaporator approach temperature. She helps plant engineers and sourcing teams size dependable chiller packages, interpret part-load performance, and balance energy use, redundancy, maintenance access, and lifecycle cost.

Leave a Reply